Jump to contentJump to page navigation: previous page [access key p]/next page [access key n]
openSUSE Leap Documentation › Virtualization Guide › Managing Virtual Machines with libvirt › Guest Installation
ContentsContents
Virtualization Guide
  1. About This Manual
  2. I Introduction
    1. 1 Virtualization Technology
    2. 2 Introduction to Xen Virtualization
    3. 3 Introduction to KVM Virtualization
    4. 4 Virtualization Tools
    5. 5 Installation of Virtualization Components
  3. II Managing Virtual Machines with libvirt
    1. 6 Starting and Stopping libvirtd
    2. 7 Guest Installation
    3. 8 Basic VM Guest Management
    4. 9 Connecting and Authorizing
    5. 10 Managing Storage
    6. 11 Managing Networks
    7. 12 Configuring Virtual Machines with Virtual Machine Manager
    8. 13 Configuring Virtual Machines with virsh
    9. 14 Managing Virtual Machines with Vagrant
  4. III Hypervisor-Independent Features
    1. 15 Disk Cache Modes
    2. 16 VM Guest Clock Settings
    3. 17 libguestfs
    4. 18 QEMU Guest Agent
  5. IV Managing Virtual Machines with Xen
    1. 19 Setting Up a Virtual Machine Host
    2. 20 Virtual Networking
    3. 21 Managing a Virtualization Environment
    4. 22 Block Devices in Xen
    5. 23 Virtualization: Configuration Options and Settings
    6. 24 Administrative Tasks
    7. 25 XenStore: Configuration Database Shared between Domains
    8. 26 Xen as a High-Availability Virtualization Host
  6. V Managing Virtual Machines with QEMU
    1. 27 QEMU Overview
    2. 28 Setting Up a KVM VM Host Server
    3. 29 Guest Installation
    4. 30 Running Virtual Machines with qemu-system-ARCH
    5. 31 Virtual Machine Administration Using QEMU Monitor
  7. VI Managing Virtual Machines with LXC
    1. 32 Linux Containers
    2. 33 Migration from LXC to libvirt-lxc
  8. Glossary
  9. A Appendix
  10. B XM, XL Toolstacks and Libvirt framework
  11. C GNU Licenses
Navigation←→
openSUSE Leap Documentation › Virtualization Guide › Managing Virtual Machines with libvirt › Guest Installation
Top
←→
Applies to openSUSE Leap 15.2

7 Guest Installation Edit source

7.1 GUI-Based Guest Installation
7.2 Installing from the Command Line with virt-install
7.3 Advanced Guest Installation Scenarios

A VM Guest consists of an image containing an operating system and data files and a configuration file describing the VM Guest's virtual hardware resources. VM Guests are hosted on and controlled by the VM Host Server. This section provides generalized instructions for installing a VM Guest.

Virtual machines have few if any requirements above those required to run the operating system. If the operating system has not been optimized for the virtual machine host environment, it can only run on hardware-assisted virtualization computer hardware, in full virtualization mode, and requires specific device drivers to be loaded. The hardware that is presented to the VM Guest depends on the configuration of the host.

You should be aware of any licensing issues related to running a single licensed copy of an operating system on multiple virtual machines. Consult the operating system license agreement for more information.

7.1 GUI-Based Guest Installation Edit source

The New VM wizard helps you through the steps required to create a virtual machine and install its operating system. There are two ways to start it: Within Virtual Machine Manager, either click Create New Virtual Machine or choose File › New Virtual Machine. Alternatively, start YaST and choose Virtualization › Create Virtual Machines for Xen and KVM.

  1. Start the New VM wizard either from YaST or Virtual Machine Manager.

  2. Choose an installation source—either a locally available media or a network installation source. If you want to set up your VM Guest from an existing image, choose import existing disk image.

    On a VM Host Server running the Xen hypervisor, you can choose whether to install a paravirtualized or a fully virtualized guest. The respective option is available under Architecture Options. Depending on this choice, not all installation options may be available.

  3. Depending on your choice in the previous step, you need to provide the following data:

    Local Installation Media (ISO image or CDROM)

    Specify the path on the VM Host Server to an ISO image containing the installation data. If it is available as a volume in a libvirt storage pool, you can also select it using Browse. For more information, see Chapter 10, Managing Storage.

    Alternatively, choose a physical CD-ROM or DVD inserted in the optical drive of the VM Host Server.

    Network Installation (HTTP, FTP, or NFS)

    Provide the URL pointing to the installation source. Valid URL prefixes are, for example, ftp://, http://, https://, and nfs://.

    Under URL Options, provide a path to an auto-installation file (AutoYaST or Kickstart, for example) and kernel parameters. Having provided a URL, the operating system should be automatically detected correctly. If this is not the case, deselect Automatically Detect Operating System Based on Install-Media and manually select the OS Type and Version.

    Network Boot (PXE)

    When booting via PXE, you only need to provide the OS Type and the Version.

    Import Existing Disk Image

    To set up the VM Guest from an existing image, you need to specify the path on the VM Host Server to the image. If it is available as a volume in a libvirt storage pool, you can also select it using Browse. For more information, see Chapter 10, Managing Storage.

  4. Choose the memory size and number of CPUs for the new virtual machine.

  5. This step is omitted when Import an Existing Image is chosen in the first step.

    Set up a virtual hard disk for the VM Guest. Either create a new disk image or choose an existing one from a storage pool (for more information, see Chapter 10, Managing Storage). If you choose to create a disk, a qcow2 image will be created. By default, it is stored under /var/lib/libvirt/images.

    Setting up a disk is optional. If you are running a live system directly from CD or DVD, for example, you can omit this step by deactivating Enable Storage for this Virtual Machine.

  6. On the last screen of the wizard, specify the name for the virtual machine. To be offered the possibility to review and make changes to the virtualized hardware selection, activate Customize configuration before install. Find options to specify the network device under Network Selection.

    Click Finish.

  7. (Optional) If you kept the defaults in the previous step, the installation will now start. If you selected Customize configuration before install, a VM Guest configuration dialog opens. For more information about configuring VM Guests, see Chapter 12, Configuring Virtual Machines with Virtual Machine Manager.

    When you are done configuring, click Begin Installation.

Tip
Tip: Passing Key Combinations to Virtual Machines

The installation starts in a Virtual Machine Manager console window. Some key combinations, such as Ctrl–Alt–F1, are recognized by the VM Host Server but are not passed to the virtual machine. To bypass the VM Host Server, Virtual Machine Manager provides the “sticky key” functionality. Pressing Ctrl, Alt, or Shift three times makes the key sticky, then you can press the remaining keys to pass the combination to the virtual machine.

For example, to pass Ctrl–Alt–F2 to a Linux virtual machine, press Ctrl three times, then press Alt–F2. You can also press Alt three times, then press Ctrl–F2.

The sticky key functionality is available in the Virtual Machine Manager during and after installing a VM Guest.

7.2 Installing from the Command Line with virt-install Edit source

virt-install is a command line tool that helps you create new virtual machines using the libvirt library. It is useful if you cannot use the graphical user interface, or need to automatize the process of creating virtual machines.

virt-install is a complex script with a lot of command line switches. The following are required. For more information, see the man page of virt-install (1).

General Options

  • --name VM_GUEST_NAME: Specify the name of the new virtual machine. The name must be unique across all guests known to the hypervisor on the same connection. It is used to create and name the guest’s configuration file and you can access the guest with this name from virsh. Alphanumeric and _-.:+ characters are allowed.

  • --memory REQUIRED_MEMORY: Specify the amount of memory to allocate for the new virtual machine in megabytes.

  • --vcpus NUMBER_OF_CPUS: Specify the number of virtual CPUs. For best performance, the number of virtual processors should be less than or equal to the number of physical processors.

Virtualization Type

  • --paravirt: Set up a paravirtualized guest. This is the default if the VM Host Server supports paravirtualization and full virtualization.

  • --hvm: Set up a fully virtualized guest.

  • --virt-type HYPERVISOR: Specify the hypervisor. Supported values are kvm, xen, or lxc.

Guest Storage

Specify one of --disk, --filesystem or --nodisks the type of the storage for the new virtual machine. For example, --disk size=10 creates 10 GB disk in the default image location for the hypervisor and uses it for the VM Guest. --filesystem /export/path/on/vmhost specifies the directory on the VM Host Server to be exported to the guest. And --nodisks sets up a VM Guest without a local storage (good for Live CDs).

Installation Method

Specify the installation method using one of --location, --cdrom, --pxe, --import, or --boot .

Accessing the Installation

Use the --graphics VALUE option to specify how to access the installation. openSUSE Leap supports the values vnc or none.

If using VNC, virt-install tries to launch virt-viewer. If it is not installed or cannot be run, connect to the VM Guest manually with you preferred viewer. To explicitly prevent virt-install from launching the viewer use --noautoconsole. To define a password for accessing the VNC session, use the following syntax: --graphics vnc,password=PASSWORD.

In case you are using --graphics none, you can access the VM Guest through operating system supported services, such as SSH or VNC. Refer to the operating system installation manual on how to set up these services in the installation system.

Passing Kernel and Initrd Files

It is possible to directly specify the Kernel and Initrd of the installer, for example from a network source.

To pass additional boot parameters, use the --extra-args option. This can be used to specify a network configuration. For details, see https://en.opensuse.org/SDB:Linuxrc.

Example 7.1: Loading Kernel and Initrd from HTTP Server 
root # virt-install --location \
"http://download.opensuse.org/pub/opensuse/distribution/leap/15.0/repo/oss" \
--extra-args="textmode=1" --name "Leap15" --memory 2048 --virt-type kvm \
--connect qemu:///system --disk size=10 --graphics vnc --network \
network=vnet_nated
Enabling the Console

By default, the console is not enabled for new virtual machines installed using virt-install. To enable it, use --extra-args="console=ttyS0 textmode=1" as in the following example: 

tux > virt-install --virt-type kvm --name sles12 --memory 1024 \
 --disk /var/lib/libvirt/images/disk1.qcow2 --os-variant sles12
 --extra-args="console=ttyS0 textmode=1" --graphics none

After the installation finishes, the /etc/default/grub file in the VM image will be updated with the console=ttyS0 option on the GRUB_CMDLINE_LINUX_DEFAULT line.

Using UEFI and Secure Boot

Install OVMF as described in Section 5.5, “Installing UEFI Support”. Then add the --boot uefi option to the virt-install command.

Secure boot will be used automatically when setting up a new VM with OVMF. To use a specific firmware, use --boot loader=/usr/share/qemu/ovmf-VERSION.bin. Replace VERSION with the file you need.

Example 7.2: Example of a virt-install command line

The following command line example creates a new SUSE Linux Enterprise Desktop 12 virtual machine with a virtio accelerated disk and network card. It creates a new 10 GB qcow2 disk image as a storage, the source installation media being the host CD-ROM drive. It will use VNC graphics, and it will auto-launch the graphical client.

KVM
tux > virt-install --connect qemu:///system --virt-type kvm  --name sled12 \
--memory 1024 --disk size=10 --cdrom /dev/cdrom --graphics vnc \
--os-variant sled12
Xen
tux > virt-install --connect xen:// --virt-type xen  --name sled12 \
--memory 1024 --disk size=10 --cdrom /dev/cdrom --graphics vnc \
--os-variant sled12

7.3 Advanced Guest Installation Scenarios Edit source

This section provides instructions for operations exceeding the scope of a normal installation, such as memory ballooning and installing add-on products.

7.3.1 Including Add-on Products in the Installation Edit source

Some operating systems such as openSUSE Leap offer to include add-on products in the installation process. If the add-on product installation source is provided via SUSE Customer Center, no special VM Guest configuration is needed. If it is provided via CD/DVD or ISO image, it is necessary to provide the VM Guest installation system with both the standard installation medium image and the image of the add-on product.

If you are using the GUI-based installation, select Customize Configuration Before Install in the last step of the wizard and add the add-on product ISO image via Add Hardware › Storage. Specify the path to the image and set the Device Type to CD-ROM.

If you are installing from the command line, you need to set up the virtual CD/DVD drives with the --disk parameter rather than with --cdrom. The device that is specified first is used for booting. The following example will install SUSE Linux Enterprise Server 15 together with SUSE Enterprise Storage extension: 

tux > virt-install --name sles15+storage --memory 2048 --disk size=10 \
 --disk /path/to/SLE-15-SP2-Full-ARCH-GM-media1.iso-x86_64-GM-DVD1.iso,device=cdrom \
 --disk /path/to/SUSE-Enterprise-Storage-VERSION-DVD-ARCH-Media1.iso,device=cdrom \
 --graphics vnc --os-variant sles15
→Chapter 8 Basic VM Guest Management←Chapter 6 Starting and Stopping libvirtd
Print this page

© 2020 SUSE